Search GDR Data
Showing results 576 - 595 of 595.
Show
results per page.
Order by:
Available Now:
Topic
Technologies
Demonstration Sites
Data Type
This dataset contains thermohydraulic measurements of fluid flow through single and dual fracture systems under controlled laboratory conditions. Experiments were conducted at Oklahoma State University using various ionic and nonionic fluids, including deep eutectic solvents (DES)...
This file was a report submitted to GTO by Mark Paster, a consultant to the GETEM project, to outline the improvements that were made between summer 2011 and spring 2013. The report focuses on six areas of model improvement:
(1) Site Specific Cost Variability;
(2) Consistency wi...
This dataset includes an Excel spreadsheet with Utah FORGE Phase 2c Well 78-32 capacity data. It also includes a readme file discussing the data which also includes the well coordinates.
This engineering design and specification document contains the applications, specifications, testing, materials, and running methods for the Open-Hole Packer. The Open Hole Packer is designed to seal 8.5 to 9.75 inch open-holes with a 7 inch casing. The design is intended to seal...
Provided here is a set of presentation slides detailing stress-dependent permeability in FORGE granitoid fractures and how fracture slip affects permeability. It outlines empirical correlations between permeability, stress, and fracture aperture, emphasizing that mechanically clos...
This comprehensive technical report documents a multi-component approach to in-situ stress characterization at the Utah FORGE EGS site that integrates Machine Learning (ML) methods for predicting near-well principal stresses around geothermal wells with the physics-based finite el...
Final Report describing regional signature detection for blind and traditional play fairways as part of Phase I of New Mexico Play Fairway Analysis. This project seeks to reduce exploration risk and identify new prospective targets using available geologic, geochemical, and geophy...
The goal of this project was to create a template (and associated form) on OpenEI to solicit crowd-sourced information sharing about various geothermal resource areas around the world. Over the past two years, twelve case studies have been researched by NREL staff testing the usa...
Operational performance requirements are needed to support development of specifications for downhole motor power sections to be used for drilling hard rock during geothermal wellbore construction. Theoretical torque specifications are derived based upon a widely-accepted rock-re...
This report covers data acquisition, instrumentation and processing of a gravity survey performed on the Glass Buttes Geothermal Exploration Project, located in Lake County, Oregon for ORMAT Technologies Inc. The survey was conducted during 21 June 2010 to 26 June 2010. The surve...
Compilation of results for mechanical and fluid flow properties of analogue outcrop samples experimental data for compressional and shear wave velocities, tensile strengths, and compressive strengths. Outcrop location and sample orientation data are documented in a separate csv file.
This document describes the design requirements for the geothermal heat pump (GHP) module being added to the existing REopt Lite web tool. This document describes the purpose, users, and functional requirements to which the modified web tool shall conform. This document will be re...
A fundamental issue in microhole drilling is that delivering high weight-on-bit (WOB), high torque rotational horsepower to a conventional drill bit does not scale down to the hole sizes necessary to realize the envisioned cost savings An optimization algorithm called a golden sec...
This document provides the applications, specifications, testing, materials, and running methods for the engineering team at PertoQuip to design the Locking Bridge Plug (LBP) and the Landing Profile (LP). This is the first step in developing a new tool for. The report includes ap...
The goal of our project was to test innovative exploration technologies using existing and new data, and to ground-truth these technologies using slim-hole core technology. The slim-hole core allowed us to understand subsurface stratigraphy and alteration in detail, and to correla...
Archive containing input/output data for distinct element reservoir modeling for Fallon FORGE. Models created using 3DEC, InSite, and in-house Python algorithms (ITASCA). List of archived files follows; please see 'Modeling Metadata.pdf' (included as a resource below) for addition...
This is the topical report that wraps up the work and results achieved during Utah FORGE Phase 2C. The zip file includes several folders containing (1) an overview; (2) the results; (3) the lessons learned; and (4) the conclusions. It also contains a folder containing appendices i...
The FORGE team is making these fracture models available to researchers wanting a set of natural fractures in the FORGE reservoir for use in their own modeling work. They have been used to predict stimulation distances during hydraulic stimulation at the open toe section of well 1...
Feasibility study completed to identify the economic and operations benefits of using a geothermal based heat pump to supplement domestic hot water production for a large county detention facility.
P and S-wave datasets and associated report studying the ability to use three-component long offset surface seismic surveys to find large aperture fractures in geothermal resources at the San Emidio geothermal resource area in Washoe County, Nevada.
Google Map