Search GDR Data

Utah FORGE 2-2439: A Multi-Component Approach to Characterizing In-Situ Stress: Laboratory, Modeling and Field Measurement Workshop Presentation

This is a presentation on A Multi-Component Approach to Characterizing In-Situ Stress at the U.S DOE FORGE EGS Site: Laboratory, Modeling and Field Measurement project by Battelle [Columbus, OH], presented by Mark Kelley. The project's objective was to characterize stress in the U...

Kelley, M. and Bunger, A. Battelle Memorial Institute

Sep 08, 2023
1 Resources
0 Stars
Publicly accessible

Utah FORGE 2-2439v2: Report on Predicting Far-Field Stresses Using Finite Element Modeling and Near-Wellbore Machine Learning for Well 16A(78)-32

This report presents the far-field stress predictions at two locations along the vertical section of Utah FORGE Well 16A (78)-32 using a physics-based thermo-poro-mechanical model. Three principal stresses in far-field were obtained by solving an inverse problem based on the near-...

Lu, G. et al University of Pittsburgh

Aug 30, 2024
2 Resources
0 Stars
Curated

Utah FORGE 2-2446: Report on Phase Field Modelling of Near-Wellbore Hydraulic Fracture Nucleation and Propagation

This is a report that describes the modelling of fracture nucleation and propagation in the near-wellbore region to understand the relationship between in situ stress and fracture patterns. A novel phase field formulation is described here, which represents fractures as a diffuse ...

Cusini, M. and Fei, F. Lawrence Livermore National Laboratory

Dec 31, 2023
1 Resources
0 Stars
Publicly accessible

Utah FORGE: Earth Model Native State Simulation Results

Utah FORGE phase 2C Native State Simulation zip contains the data used for the boundary conditions and subsequent native state simulation results obtained using the simulation code FALCON. Data are from the nodes of the simulation domain, with used a uniform 50m spacing over a 250...

Podgorney, R. Energy and Geoscience Institute at the University of Utah

Jul 16, 2019
2 Resources
0 Stars
Publicly accessible

Utah FORGE: Core Material Friction Experiments

The following folders contain 3 friction experiments on Utah FORGE core material from depths of 6735 8533ft. The experiment conditions range from 100% relative humidity at room temperature to fluid-saturated at 110C. Experiments were done on both intact samples in a single-direct ...

Marone, C. et al Pennsylvania State University

Mar 15, 2023
7 Resources
0 Stars
Curated

Utah FORGE 2-2439v2: Characterizing In-Situ Stress with Laboratory Modelling and Field Measurements 2024 Annual Workshop Presentation

This is a presentation on A Multi-Component Approach to Characterizing In-Situ Stress at the Utah FORGE Site: Laboratory Modelling and Field Measurements project by The University of Pittsburgh, presented by Andrew Bunger. The project characterizes the stress in the Utah FORGE EGS...

Bunger, A. Energy and Geoscience Institute at the University of Utah

Sep 04, 2024
1 Resources
0 Stars
Curated

Utah FORGE: Phase 3 Magnetotelluric (MT) Data

New high-quality tensor MT data at 122 sites, including the vertical magnetic field and utilizing ultra-remote referencing, have been acquired over the Utah FORGE project area. The results will be used to delineate the densities of faults and fractures in crystalline basement rock...

Wannamaker, P. and Maris, V. Energy and Geoscience Institute at the University of Utah

Oct 01, 2020
5 Resources
0 Stars
Publicly accessible

Utah FORGE: Targeting Geothermal Resources with Geodetic Strain Data Paper

The paper linked below offers an initial assessment of a new method to target potential geothermal resources on the regional scale. The method is based on seeking relationships between geologic structures and geodetic observations of regional tectonic strain.

Blewitt, G. et al Energy and Geoscience Institute at the University of Utah

Oct 01, 2004
1 Resources
0 Stars
Curated

Utah FORGE 3-2535: Numerical Modeling of Energized Steel-Casing Source for Imaging Stimulated Zone

This short report details and tests the workflow that will be used to simulate steel well casings in deviated production/extraction boreholes at at the Utah FORGE site. Boreholes will be electrically energized and will serve as data sources for future proposed electromagnetic bore...

Um, E. et al Lawrence Berkeley National Laboratory

Nov 15, 2022
4 Resources
0 Stars
Curated

Utah FORGE: Southwestern Utah Magnetotelluric (MT) Data

This comprehensive magnetotellurics (MT) dataset, which covers southwestern Utah, integrates 600 sites from various surveys, including those from the Utah FORGE, SubTER, and Play Fairway projects, all of which are linked below. The core of this dataset is the use of a 3D finite el...

Wannamaker, P. and Marris, V. Energy and Geoscience Institute at the University of Utah

Jan 22, 2024
4 Resources
0 Stars
Publicly accessible

Utah FORGE: Heat Flow Contours and Well Data

This submission contains a shapefile of heat flow contour lines around the FORGE site located in Milford, Utah. The model was interpolated from data points in the Milford_wells shapefile. This heat flow model was interpolated from 66 data points using the kriging method in Geostat...

Moore, J. Energy and Geoscience Institute at the University of Utah

Mar 09, 2016
2 Resources
0 Stars
Publicly accessible

Utah FORGE 3-2535: Modeling Studies of Energized Steel-Casing Source EM Method for Detecting Stimulated Zone

Numerical modeling Studies for electromagnetic (EM) Data Acquisition Survey Design this milestone report describes the 3D modeling studies of energized steel-casing source electromagnetic method for detecting stimulated zone at the Utah FORGE Site. FORGE project 3-2535 is planning...

Um, E. et al Lawrence Berkeley National Laboratory

Feb 06, 2023
4 Resources
0 Stars
Curated

Utah FORGE 2439: Well 16B(78)-32 Field-Test Data from Mini-Frac Tests

This submittal includes the field-test data collected during stress tests conducted in the Utah FORGE 16B(78)-32 wellbore to measure/characterize the stresses in the geothermal reservoir. The type of stress test performed is referred to as a mini-frac test or a micro-frac test. Th...

Kelley, M. et al Battelle Memorial Institute

Jul 02, 2023
3 Resources
0 Stars
Curated

Utah FORGE 3-2535: Building a 3D Resistivity Model for Simulation and Survey Design of EM Measurements

The included report outlines the creation of three 3D resistivity models that will be used to determine the sensitivity of EM measurements for the hypothetical stimulated reservoir at FORGE as well as for EM survey design. FORGE project 3-2535 is planning on using a casing source ...

Alumbaugh, D. et al Lawrence Berkeley National Laboratory

Dec 01, 2022
5 Resources
0 Stars
Curated

Utah FORGE 3-2535: Compilation of Geodetic Data and Estimation of Associated Deformation

Report on possible geodetic signature of the 3 stimulations in April 2022 as well as a comparison with existing InSAR data gathered over the site before, during, and after the stimulation. In geothermal production it is important to understand the existing stress field and the cha...

Vasco, D. et al Lawrence Berkeley National Laboratory

Apr 29, 2022
4 Resources
0 Stars
Curated

Utah FORGE: Powder X-ray Diffraction Data from Well 16A(78)-32 Core

This dataset from Lawrence Livermore National Laboratory (LLNL) consists of four raw X-ray diffraction (XRD) scans and preliminary results of quantitative XRD analysis. The scanned samples were prepared from four subcores, which came from various depths of the FORGE well 16A(78)-3...

Kroll, K. et al Lawrence Livermore National Laboratory

Jul 27, 2023
1 Resources
0 Stars
Publicly accessible

Utah FORGE 3-2535: Preliminary Report on Development of a Reservoir Seismic Velocity Model

This report describes the development of a preliminary 3D seismic velocity model at the Utah FORGE site and first results from estimating seismic resolution in the generated fracture volume during Stage 3 of the April 2022 stimulation. A preliminary 3D velocity model for the larg...

Gritto, R. Array Information Technology

Jan 30, 2023
1 Resources
0 Stars
Curated

Utah FORGE: Development of a Reservoir Seismic Velocity Model and Seismic Resolution Study

This is data from and a final report on the development of a 3D velocity model for the larger FORGE area and on the seismic resolution in the stimulated fracture volume at the bottom of well 16A-32. The velocity model was developed using RMS velocities of the seismic reflection su...

Vasco, D. and Chan, C. Array Information Technology

Apr 30, 2022
2 Resources
0 Stars
Curated

Utah FORGE 3-2417: Simulations for Distributed Acoustic Sensing Strain Signatures as an Indicator of Fracture Connectivity

This dataset encompasses simulations of strain signatures from both hydraulically connected and "near-miss" fractures in enhanced geothermal systems (EGS). The files and results are presented from the perspective of digital acoustic sensing's (DAS) potential to differentiate the t...

Ward-Baranyay, M. et al Rice University

Jan 01, 2023
4 Resources
0 Stars
Curated

Utah FORGE 2439: A Multi-Component Approach to Characterizing In-Situ Stress

Core-based in-situ stress estimation, Triaxial Ultrasonic Velocity (labTUV) data, and Deformation Rate Analysis (DRA) data for Utah FORGE well 16A(78)-32 using triaxial ultrasonic velocity and deformation rate analysis. Report documenting a multi-component approach to characterizi...

Bunger, A. et al Battelle Memorial Institute

Dec 13, 2022
4 Resources
0 Stars
Curated

Utah FORGE: Report and Associated Data from Measuring and Modeling Deformation 2018 through 2024

The report provided here describes research activities between August 16th, 2018 and July 30th, 2024. The goals of the research activities are to conduct an Interferometric Synthetic Aperture Radar (InSAR) analysis and Ground Surface Deformation Modeling at the Utah FORGE site. In...

Feigl, K. and Batzli, S. University of Wisconsin Madison

Aug 16, 2018
6 Resources
0 Stars
Curated