Search GDR Data
Showing results 1 - 25 of 48.
Show
results per page.
Order by:
Available Now:
Topic
Technologies
Demonstration Sites
Data Type
Data includes characterization results for novel thermoelectric materials developed specifically for power generation from low temperature geothermal brines. Materials characterization data includes material density, thickness, resistance, Seebeck coefficient. This research was ca...
The PoroTomo team has completed inverse modeling of the three data sets (seismology, geodesy, and hydrology) individually, as described previously. The estimated values of the material properties are registered on a three-dimensional grid with a spacing of 25 meters between nodes....
This report describes a comprehensive review of 49 existing supercritical geothermal wells to inform future geothermal drilling attempts and avoid previous failure points and understand material and testing limitations, while collating information gathered in a publicly accessible...
Numerical modeling on fused silica cylindrical materials for predicting overpressures required to fracture an homogeneous pure (surrogate) material with known mechanical properties similar to igneous rock materials and later compare these values to experimental overpressures obtai...
The information given in this file pertains to Argonne life-cycle analyses (LCAs) of the plant cycle stage for a set of ten new geothermal scenario pairs, each comprised of a reference and improved case. These analyses were conducted to compare environmental performances among the...
In addition to the foam data that were obtained from literature and that were collected from the current study, simulation data was also generated from finite element analysis (FEA) conducted in this study using COMSOL Multiphysics software. The FEA models were built to simulate t...
This dataset compiles information on geothermal wells drilled into supercritical and near-supercritical conditions, with a focus on drilling and completion materials, fluid chemistry, and laboratory validation studies. The data are drawn from well reports, scientific literature, a...
The following folders contain 3 friction experiments on Utah FORGE core material from depths of 6735 8533ft. The experiment conditions range from 100% relative humidity at room temperature to fluid-saturated at 110C. Experiments were done on both intact samples in a single-direct ...
This dataset provides a set of experimental data on the performance of lost circulation materials (LCMs) used in geothermal drilling operations. It includes results from four distinct tests: thermal degradation, viscosity measurements, compression tests, and high-temperature flow ...
The Closed-Loop Geothermal Working Group and the National Renewable Energy Laboratory (NREL) have studied the performance of disc-shaped and linear thermal enhancements (conductive material introduced around a wellbore) in closed-loop geothermal systems. COMSOL models were develop...
This dataset includes an Excel file with the results of B-value tests to determine the magnitude of the back pressure required for full saturation of Sierra White granite samples. Test were conducted on cylindrical rock specimens of Sierra White granite in a custom water pressuriz...
There is an ongoing effort at Oak Ridge National Laboratory to develop a unique experimental capability for investigating flow through porous and fractured media using neutron imaging techniques. This capability is expected to support numerous areas of investigation associated wit...
Rheology data obtained from flow loop tests, performed using different lost circulation materials (LCM) to study their effect on fluid rheology and wellbore hydraulics. The sealing performance of different LCM was tested using different fracture sizes. Five academic papers / repor...
This submission includes a methods report and an accompanying Excel dataset documenting temperature-dependent Mode-I fracture toughness (KIC) measurements for Utah FORGE granite obtained using semi-circular bending (SCB) tests in accordance with the ISRM Suggested Method. Testing ...
Life cycle analysis (LCA) is an environmental assessment method that quantifies the environmental performance of a product system over its entire lifetime, from cradle to grave. Based on a set of relevant metrics, the method is aptly suited for comparing the environmental performa...
Submitted data include simulations related to underground thermal battery (UTB) simulations described in Modeling and efficiency study of large scale underground thermal battery deployment, presented at GRC, October 2021.
The UTB is comprised of a tank of water, a helical heat ex...
Test report for detonation velocity measurements. A series of tests were conducted to determine reaction rate and general behavior of aluminum (AL) and magnesium (MG) powder mixtures (metalized explosives) with Bullseye double-base smokeless propellant. Given the indeterminate sen...
This is a technical report for the Probabilistic Estimation of Seismic Response Using Physics Informed Recurrent Neural Networks project. The report describes the process of designing a recurrent neural network (RNN) to predict induced seismicity. Background material is included t...
High-pressure and high-temperature (HPHT) lost circulation material (LCM) rheology test results, LCM particle size distributions (PSD) analysis, and HPHT LCM fluid loss test results. Three academic papers / reports derived from this research are also presented.
This is an Excel spreadsheet containing the results of X-ray fluorescence from well 56-32 sludge samples. The instrumentation used was a Olympus Vanta M series handheld XRF analyzer. A glass (SiO2) "blank" was analyzed at the beginning and end of each sample batch to detect contam...
The main goal of this project is to develop an annular isolation system capable to withstand geothermal downhole conditions and mitigate the problems experienced by conventional packers in FORGE wells. This materials testing report is based on thermoplastic and elastomeric materia...
Borehole W1 is a NQ core hole drilled at our test site in Socorro. The rock is rhyolite. Borehole W1 which was used to test gas-gas explosive mixtures is 55 feet deep with casing (pinkish in the drawing) set to 35 feet. The model is a representation of the borehole and the hol...
Wells for Engineered Geothermal Systems (EGS) typically occur in conditions presenting significant challenges for conventional rotary and percussive drilling technologies: granitic rocks that reduce drilling speeds and cause substantial equipment wear. Thermal spallation drilling,...
This is a link to the open access, published dataset and modeling that supports a feasibility study of Reservoir Thermal Energy Storage (RTES) in the Portland Basin, Oregon, USA.
Citation:
Burns, E.R., 2020, SUTRA model used to evaluate Saline or Brackish Aquifers as Reservoirs f...
This is the Phase 3 native state model update. The Phase 3 numerical model represents a significant subsurface volume below the FORGE site footprint. The model domain of 4.0 km x 4.0 km x 4.2 km is located approximately between depths of 4000 to 4200 meters below land surface. Thi...
Google Map