Search GDR Data
Showing results 26 - 50 of 66.
Show
results per page.
Order by:
Available Now:
Topic
Technologies
Demonstration Sites
Data Type
Numerical modeling Studies for electromagnetic (EM) Data Acquisition Survey Design this milestone report describes the 3D modeling studies of energized steel-casing source electromagnetic method for detecting stimulated zone at the Utah FORGE Site. FORGE project 3-2535 is planning...
To reduce the geothermal exploration risk, a feasibility study is performed for a deep direct-use system proposed at the West Virginia University (WVU) Morgantown campus. This study applies numerical simulations to investigate reservoir impedance and thermal production. Because of...
Report on possible geodetic signature of the 3 stimulations in April 2022 as well as a comparison with existing InSAR data gathered over the site before, during, and after the stimulation. In geothermal production it is important to understand the existing stress field and the cha...
This report contains the results of research conducted to make measurements in the FORGE wells to map flowing fractures and estimate their flow magnitudes in real time. Implementation of the project had two substantial goals: (1) to locate flowing fractures at FORGE and estimate t...
The included report outlines the creation of three 3D resistivity models that will be used to determine the sensitivity of EM measurements for the hypothetical stimulated reservoir at FORGE as well as for EM survey design. FORGE project 3-2535 is planning on using a casing source ...
The primary objective of our current research is to develop a computational test bed for evaluating borehole techniques to enhance fluid flow and heat transfer in enhanced geothermal systems (EGS). Simulating processes resulting in hydraulic fracturing and/or the remobilization of...
The problem of loss circulation in geothermal wells is inherently challenging due to high temperatures, brittle rocks, and presence of abundant fractures. Because of the inherent challenges in geothermal environments, there are limitations in selecting proper lost circulation mate...
Groundwater flow model for the island of Oahu. Data is from the following sources:
Rotzoll, K., A.I. El-Kadi. 2007. Numerical Ground-Water Flow Simulation for Red Hill Fuel Storage Facilities, NAVFAC Pacific, Oahu, Hawaii Prepared TEC, Inc. Water Resources Research Center, Univer...
This submission contains datasets and a final manuscript associated with a project simulating carbon dioxide push-pull into a conjugate fault system modeled after Dixie Valley-
sensitivity analysis of significant parameters and uncertainty prediction by data-worth analysis.
Datas...
Plugging of fracture porosity from mineral precipitation due to injecting cold water into a a geothermal reservoir can impact the overall permeability of the fracture network in the reservoir. This can have serious ramifications on the efficiency of the geothermal resource. Geoche...
This is a presentation on the Strain Sensing Array to Characterize Deformation at the FORGE Site project by Clemson University, presented by Lawrence Murdoch. The project's objective was to evaluate the feasibility of measuring and interpreting tensor strain data to improve the pe...
This is a presentation on the Evolution of Permeability and Strength Recovery of Shear Fractures Under Hydrothermal Conditions project by the U.S. Geological Survey, presented by Dr. David Lockner. The project's objective was to determine how thermal, hydraulic, mechanical, and ch...
DEEPEN stands for DE-risking Exploration of geothermal Plays in magmatic ENvironments.
As part of the development of the DEEPEN 3D play fairway analysis (PFA) methodology for magmatic plays (conventional hydrothermal, superhot EGS, and supercritical), weights needed to be develop...
This paper presents a generalized form of the displacement correlation method (the GDC method), which can use any linear or quadratic finite element type with homogeneous meshing without local refinement. These two features are critical for modeling dynamic fracture propagation pr...
This is the Phase 3 native state model update. The Phase 3 numerical model represents a significant subsurface volume below the FORGE site footprint. The model domain of 4.0 km x 4.0 km x 4.2 km is located approximately between depths of 4000 to 4200 meters below land surface. Thi...
This submission comprises two downloadable .zip archives. Each archive contains spreadsheets with 3-D data and a .txt document describing the data. The Mesh Files .zip download contains data regarding the lithologic contacts of the granitoid and overlying sedimentary basin fill. T...
This is a presentation on the Closing the Loop Between In-situ Stress Complexity and EGS Fracture Complexity project by Lawrence Livermore National Laboratory, presented by Dr. Matteo Cusini. The project's objective was to employ a combination of high-fidelity simulations and true...
To better understand the heat production, electricity generation performance, and economic viability of closed-loop geothermal systems in hot-dry rock, the Closed-Loop Geothermal Working Group a consortium of several national labs and academic institutions has tabulated time-depe...
The files in this submission describes the results of a series of stress measurement and hydraulic fracturing experiments conducted at the Sanford Underground Research Facility (SURF) in Lead, SD. This report describes the accomplishments of the kISMET (permeability (k) and Induce...
This collection includes datasets used for the analyses and modeling of low-temperature geothermal resources at the U.S. Army's Detroit Arsenal located in Warren, Michigan. This project file includes tabular and geospatial data accessed from publicly available repositories held by...
The U.S. Department of Energy Geothermal Vision (GeoVision) Study is currently looking at the potential to increase geothermal deployment in the U.S. and to understand the impact of this increased deployment. This paper reviews 31 performance, cost, and financial parameters as inp...
Hydraulic fracturing is currently the primary method for stimulating low-permeability geothermal reservoirs and creating Enhanced (or Engineered) Geothermal Systems (EGS) with improved permeability and heat production efficiency. Complex natural fracture systems usually exist in ...
This is the topical report that wraps up the work and results achieved during Utah FORGE Phase 2C. The zip file includes several folders containing (1) an overview; (2) the results; (3) the lessons learned; and (4) the conclusions. It also contains a folder containing appendices i...
This submission contains the presentation slides and recordings from the first 98 EGS Collab Modeling and Simulation Working Group teleconferences. These teleconferences served three objectives for the project: 1) share simulation results, 2) communicate field activities and resul...
The evolution of flow pattern along a single fracture and its effects on heat production is a fundamental problem in the assessments of engineered geothermal systems (EGS). The channelized flow pattern associated with ubiquitous heterogeneity in fracture aperture distribution caus...
Google Map