Search GDR Data

Utah FORGE: Fluid Injection Induced Shearing Experiments on Fractured Granitoid at Elevated Temperatures

This repository contains experimental data from a series of fluid injection-induced shearing tests conducted on Utah FORGE granitoid. The experiments were performed using an aluminum triaxial pressure vessel (TEMCO) apparatus at Pennsylvania State University. The primary aim was t...

Elsworth, D. et al Pennsylvania State University

Aug 12, 2024
16 Resources
0 Stars
Curated

Utah FORGE: Temperature-Dependent Fracture Seismicity from Fluid Injection Experiments

This dataset contains experimental data from fluid injection experiments conducted to investigate the influence of temperature on fracture seismicity. The experiments were performed on granite samples from Utah FORGE. The samples were prepared with a 30-degree inclined fracture an...

Wang, J. et al Pennsylvania State University

Feb 29, 2024
4 Resources
0 Stars
Curated

Utah FORGE: Hydrothermal Friction-Hydraulic Transmissivity Laboratory Experiments

Submission includes data from laboratory slide-hold-slide tests, combined with flow through tests, conducted on Westerly granite with 30 degree sawcut. Tests were conducted with a constant confining pressure of 30 MPa with an average pore pressure of 10 MPa at temperatures of 23 a...

Jeppson, T. and Lockner, D. United States Geological Survey

Feb 24, 2022
1 Resources
0 Stars
Curated

Utah FORGE: Slide-Hold-Slide Experiments on Westerly Granite at Temperatures up to 250 Degrees C

Laboratory slide-hold-slide tests were conducted in a conventional triaxial deformation configuration on 1-inch diameter cylindrical cores of Westerly granite bisected by a sawcut oriented at 30 degrees from vertical. Tests were conducted at a constant confining pressure of 30 MPa...

Jeppson, T. et al United States Geological Survey

Oct 10, 2023
2 Resources
0 Stars
Curated

Utah FORGE: Fault Shear Reactivation Experimental Data for Fluid Injection-Rate Controls on Seismic Moment

Included are experimental data recorded from shear experiments that specifically explore the link between fluid-injection rate and seismic moment resulting from shear reactivation of laboratory faults. Raw mechanical data from three experiments are included alongside corresponding...

Roseboom, M. et al Pennsylvania State University

Nov 07, 2023
6 Resources
0 Stars
Curated

Utah FORGE 5-2615: Well 58-32 and 78-32 Poroelastic Properties

Lab data on permeability, grain bulk modulus, drained bulk modulus, Skempton's pore pressure coefficient, and Biot's effective stress coefficient for Utah Forge Well 58-32 and Well 78-32. Work done as part of project number 5-2615 by the University of Oklahoma.

Ghassemi, A. and Zhou, X. University of Oklahoma

Oct 31, 2022
2 Resources
0 Stars
Publicly accessible

Utah FORGE: Core Material Friction Experiments

The following folders contain 3 friction experiments on Utah FORGE core material from depths of 6735 8533ft. The experiment conditions range from 100% relative humidity at room temperature to fluid-saturated at 110C. Experiments were done on both intact samples in a single-direct ...

Marone, C. et al Pennsylvania State University

Mar 15, 2023
7 Resources
0 Stars
Curated

Thermal-Hydrological-Mechanical Modelling of Stockton University Reservoir Cooling System, Large Scale Grid

Mesh, properties, initial conditions, injection/withdrawal rates for modeling thermal, hydrological, and mechanical effects of fluid injection to and withdrawal from ground for Stockton University reservoir cooling system (aquifer storage cooling system), Galloway, New Jersey, on ...

Smith, J. et al Lawrence Berkeley National Laboratory

Feb 26, 2021
15 Resources
0 Stars
Publicly accessible

Laboratory Evaluation of EGS Shear Stimulation-Test 001

This is the results of an initial setup-shakedon test in order to develop the plumbing system for this test design. a cylinder of granite with offset holes was jacketed and subjected to confining pressure and low temperature (85C) and pore water pressure. Flow through the sample w...

Bauer, S. Sandia National Laboratories

Jul 29, 2014
1 Resources
0 Stars
Publicly accessible

Utah FORGE 5-2557: Fluid and Temperature in Fracture Mechanics and Coupled THMC Processes Workshop Presentation

This is a presentation on the Role of Fluid and Temperature in Fracture Mechanics and Coupled Thermo-Hydro-Mechanical-Chemical (THMC) Processes for Enhanced Geothermal Systems project by Purdue University, presented by Distinguished Professor of Physics & Astronomy, Laura J. Pyrak...

Pyrak-Nolte, L. Purdue University

Sep 08, 2023
1 Resources
0 Stars
Publicly accessible

Utah FORGE: Stress Logging Data

This spreadsheet consist of data and graphs from deep well 58-32 stress testing from 6900 7500 ft depth. Measured stress data were used to correct logging predictions of in situ stress. Stress plots shows pore pressure (measured during the injection testing), the total vertical in...

McLennan, J. Energy and Geoscience Institute at the University of Utah

Mar 14, 2018
1 Resources
0 Stars
Publicly accessible

Utah FORGE: Fault Reactivation Through Fluid Injection Induced Seismicity Laboratory Experiments

Included are results from shear reactivation experiments on laboratory faults pre-loaded close to failure and reactivated by the injection of fluid into the fault. The sample comprises a single-inclined-fracture (SIF) transecting a cylindrical sample of Westerly granite. All expe...

Yu, J. et al Pennsylvania State University

Jul 01, 2023
27 Resources
0 Stars
Curated

University of Illinois Campus Deep Direct-Use Feasibility Study Thermal Properties of Geologic Formations in Illinois Basin

Thermal property data for rocks and and minerals and unconsolidated (glacial) sediments units from within and outside the Illinois Basin were compiled for modeling heat transport in the subsurface.

Lin, Y. et al University of Illinois

Mar 30, 2018
6 Resources
0 Stars
Publicly accessible

Utah FORGE: Friction-Permeability-Seismicity Laboratory Experiments with Non-Linear Acoustics

Laboratory experimental data on saw-cut interface of Westerly Granite and Utah Forge granitoid rocks. Experiments include velocity-stepping and fluid pressure stepping experiments. Mechanical data from 3 ISCO pumps connected to a Temco pressure vessel measure axial, confining and ...

Eijsink, A. and Elsworth, D. Pennsylvania State University

Jul 08, 2022
2 Resources
0 Stars
Curated

Utah FORGE: Phase 3 Native State Model 2022 Update

This is the Phase 3 native state model update. The Phase 3 numerical model represents a significant subsurface volume below the FORGE site footprint. The model domain of 4.0 km x 4.0 km x 4.2 km is located approximately between depths of 4000 to 4200 meters below land surface. Thi...

Podgorney, R. and Liu, R. Idaho National Laboratory

Jul 29, 2022
1 Resources
0 Stars
Curated

University of Illinois Campus Deep Direct-Use Feasibility Study Porosity and Permeability of Rock Formations

Porosity and permeability data from published and unpublished sources for the St. Peter and Mt. Simon Sandstones in the Illinois Basin.

Damico, J. et al University of Illinois

Mar 30, 2018
4 Resources
0 Stars
Publicly accessible

Using Fully Coupled Hydro-Geomechanical Numerical Test Bed to Study Reservoir Stimulation with Low Hydraulic Pressure

This paper documents our effort to use a fully coupled hydro-geomechanical numerical test bed to study using low hydraulic pressure to stimulate geothermal reservoirs with existing fracture network. In this low pressure stimulation strategy, fluid pressure is lower than the minimu...

Fu, P. et al Lawrence Livermore National Laboratory

Jan 31, 2012
2 Resources
0 Stars
Publicly accessible

Distributed Acoustic Sensing (DAS) for Periodic Hydraulic Tests: Laboratory Data

These data were collected in the laboratory located at California State University Long Beach. They consist of DAS data collected from a fiber optic cable placed in a tank of water, subjected to oscillating head. These tests are described in the article linked below.

Coleman, T. California State University

Feb 27, 2015
5 Resources
0 Stars
Curated

Effective Elastic and Neutron Capture Cross Section Calculations Corresponding to Simulated Fluid Properties from CO2 Push-Pull Simulations

The submission contains a .xls files consisting of 10 excel sheets, which contain combined list of pressure, saturation, salinity, temperature profiles from the simulation of CO2 push-pull using Brady reservoir model and the corresponding effective compressional and shear velocity...

Chugunov, N. and Altundas, B. Lawrence Berkeley National Laboratory

Mar 07, 2018
1 Resources
0 Stars
Publicly accessible

StimuFrac Compressibility as a Function of CO2 Molar Fraction

Compressibility values were obtained in a range of pressures at 250degC by employing a fixed volume view cell completely filled with PAA aqueous solution and injecting CO2 at constant flow rate (0.3mL/min). Pressure increase as a function of supercritical CO2 (scCO2) mass fraction...

A., C. Pacific Northwest National Laboratory

Apr 29, 2016
1 Resources
0 Stars
Publicly accessible

Utah FORGE: Well 16A(78)-32/Well16B(78)-32 Circulation Test Data

This dataset encompasses the collected data and associated reports from the low-rate injection circulation test conducted on wells 16A(78)-32 and 16B(78)-32 in July 2023 at Utah FORGE. It includes comprehensive raw circulation data, captured by Pason and Schlumberger (SLB). The da...

Mclennan, J. and Xing, P. Energy and Geoscience Institute at the University of Utah

Jul 19, 2023
1 Resources
0 Stars
Publicly accessible

Foam Fracturing Fluid Half-life Experimental Data

Foam thermal stability was studies at Temple University in collaboration with Oak Ridge National Lab (ORNL). The goal of this project is to explore thermally stable foams as hydrofracking fluid media for potential applications in enhanced geothermal system (EGS). Data generated fr...

Thakor, V. et al Temple University

May 20, 2022
1 Resources
0 Stars
Publicly accessible

Finite Element Analysis (FEA) for Water-Foam Fracturing of Granite Rock

In addition to the foam data that were obtained from literature and that were collected from the current study, simulation data was also generated from finite element analysis (FEA) conducted in this study using COMSOL Multiphysics software. The FEA models were built to simulate t...

Thakor, V. et al Temple University

May 04, 2021
1 Resources
0 Stars
Publicly accessible

High-Pressure and High-Temperature (HPHT) Lost Circulation Material (LCM) Testing

High-pressure and high-temperature (HPHT) lost circulation material (LCM) rheology test results, LCM particle size distributions (PSD) analysis, and HPHT LCM fluid loss test results. Three academic papers / reports derived from this research are also presented.

Salehi, S. and Vivas, C. University of Oklahoma

Nov 30, 2021
6 Resources
0 Stars
Publicly accessible

Pressure-Temperature Simulation at Brady Hot Springs

These files contain the output of a model calculation to simulate the pressure and temperature of fluid at Brady Hot Springs, Nevada, USA. The calculation couples the hydrologic flow (Darcy's Law) with simple thermodynamics. The epoch of validity is 24 March 2015. Coordinates are ...

Feigl, K. Temple University

Jul 11, 2017
3 Resources
0 Stars
Publicly accessible

1 2 3 4 5 Next >>